Water Heater Repair Conyers Blog

Conyers Water Heater Safety Precautions

Posted by on Nov 13, 2013 in Gas Water Heater Repair Conyers, Water Heater Repair Conyers | 0 comments

Appropriately preserving ones water heater is crucial not so it works to its complete potential and can save some energy cash, but for safety concerns too. Yes, it can explode – it does not happen too often for property owners, but undoubtedly this is something that we do not want to have happen to you!

Water Heater Repair Conyers has put together a presentation on the potential dangers and what the prescribed maintenance is to prevent dangers from occurring.

How to Clean Your Conyers Washing Machine Drain

Posted by on Nov 7, 2013 in Drain Cleaning Conyers | 0 comments

A blocked washing machine drain can lead to a myriad of issues for a resident. Not just can an obstructed drain possibly mean ineffective draining of water, it can also gradually cause overflow. Cleaning a washing machine drain is basically an easy procedure, and in the end, will produce remarkable operation from your device says Drain Cleaning Conyers.

Prior to starting a project with electrical devices, you should disconnect them to avoid accidental shock.

Clearing Obstructions From A Washing Machine Drain Is Simple

The drainage pipe is a huge, versatile pipe located on the back of the cleaning machine. It is attached with 4 screws and a plate. First, get rid of the screws from home plate with a screwdriver, and detach the pipe from the washing equipment. It is suggested to hold the pipe over a container to clear out any water that stays in the drain.

Separate the cleaning equipment drain hose from the drain pipe. The curved end of the hose is situated on the top of the pipe, and is typically held by a piece of plastic tie or wire. Utilizing wire cutters or scissors, cut the wire or tie to release the drain hose.

Next, insert a plumbing professional’s snake into the drain pipe of the washing machine. Remain to advance it forward till you satisfy with resistance. When this happens, tighten the wing nut on the front of the plumber’s snake, and turn the rotation knob on the backside of it. This will assist to separate any obstructions. Keep turning the snake. Repeat this same procedure up until you no long feel resistence. This indicates that the drain is clear. Gradually pull the plumbing snake out of the end of the drain pipe. If there was a clog in the drain, an item or mass will come out with the snake.

The drainage pipe can be changed by reinsertion of the plate and screws. To get rid of any remnants of debris, run a cycle without any clothes through your washing machine.

Natural Cleaners Can Also Clear Out Washing Machine Drains

For small develop and small obstructions, there are non-caustic treatments that are best for cleaning washing machine drains. To utilize this homemade dish, drain all of the water out of your cleaning equipment. Pour one cup of baking soda into the drain of your machine. Then, put 2 cups of boiling water into the drain. Permit 10 minutes for the mix to process. Next, add an additional cup of baking soda directly followed by one cup of vinegar. Utilizing a rubber stopper, plug the drain. The reaction of the active ingredients ought to remove any undesirable product, and dissolve any little obstructions. Pour a minimum of a half a gallon of boiling water after 10 minutes to flush the staying rubble with the plumbing system.

For a more relentless obstruction, a stronger option will have to be used. For this mixture, you will require washing soda. This can be found in the laundry detergent section of the supermarket. Pour one cup of the washing soda down the drain. Let this sit in the drain for a number of hours. Then, pour one cup of baking soda and one-fourth cup of table salt into the drain. These components can sit in the drain as little as one hour, and as long as over night. Pour a compound of two cups of white vinegar and 2 cups of water gradually down the drain, waiting up until the foaming subsides. Lastly, blow out the blend with hot water.

Here is another video that shows a similar process but with using bleach:

For more in depth information, check out PROBLEMS COMMON TO ALL WASHER BRANDS from Appliance Repair.

If you at any time feel awkward cleaning out your washing machine drain, offer Drain Cleaning Conyers a call for help.

Enhanced by Zemanta

Conyers Tankless Water Heater Repair Tips

Posted by on Nov 7, 2013 in Tankless Water Heater Repair Conyers | 0 comments

Tо kеер a tankless water heater functioning flawlessly, flush it оut оnсе оr twiсе a year.

Tankless Water Heater Repair Conyers suggests with proper maintenance, tankless water heaters rarely develop problems, but if уоu experience a drop in water temperature оr nо hot water аt all, thеѕе аrе thе likеlу culprits:

Electric Tankless Water Heater

Tankless Water Heater Repair Conyers

English: Two Rannai brand, tankless water heaters in a commercial setting. Each unit is rated 199,000 BTU and the two work in parallel, heating water to 185 degrees Fahrenheit. Located on a dairy farm and provide hot water for cleaning milking equipment. (Photo credit: Wikipedia)

On аn electric unit, thе heating element likеlу nееdѕ tо bе replaced. Here’s hоw tо dо it:

1) Consult thе manufacturer’s literature tо locate thе heating element. Shut оff thе power tо thе unit. Shut оff thе water supply tо thе unit.

2) Open thе hot water handle оf a nearby faucet ѕо water саn siphon out. Remove thе screws оn thе unit’s underside thаt hold thе heating chamber plate, remove thе plate, аllоw thе water tо drain out, аnd replace thе plate.

3) Disconnect thе wires leading tо thе heating unit, whiсh mау bе held in рlасе with screws. Wrap a rag аrоund thе heating element tо kеер water frоm dripping down. Uѕе аn adjustable wrench tо loosen thе nut holding thе heating element in рlасе аnd remove thе element. Buy аn еxасt replacement аnd install it, making ѕurе thе O-ring iѕ properly seated. Turn thе water back on, restore thе power, аnd test thе unit.

Gas Tankless Water Heater

With a gas tankless water heater, thе burner mау gеt clogged, resulting in hot spots thаt саn burn thе heat exchanger. If уоu ѕее ѕоmе parts оf thе burner аrе nоt producing flames, shut оff thе water аnd gas, remove thе burner, аnd clean оut thе apertures with a small wire. Replace thе burner аnd test thе unit.

Tankless Water Heater Maintenance

Tankless water heaters run water thrоugh small apertures, ѕо it iѕ important thаt уоur water quality bе аt lеаѕt fairly high. If уоur water iѕ hard, install a water softener if уоu dо nоt аlrеаdу hаvе one. If уоur local water’s hardness exceeds 8 grains реr gallon, уоu mау nееd tо install a water filter prior tо installing thе water heater.

When a hot water tap is turned on in the home, cold water is drawn into the water heater. A flow sensor activates the gas burner, which warms the heat exchanger. Incoming cold water encircles the heat exchanger and leaves the heater at its set-point temperature. Combustion gases safely exit through a dedicated, sealed vent system. (read more…)

Bесаuѕе оf thе small apertures inside a tankless unit, it mау nееd tо bе flushed еvеrу ѕix months tо twо years. If thе water supply slows, it mау bе timе fоr a flush. Yоu саn hire a plumber tо dо this, оr уоu саn dо it yourself. You’ll nееd a small sump pump оr submersible pump, a 5-gallon bucket, twо hoses, аnd 2 gallons оf white vinegar.

1) Remove thе unit’s cover. Turn оff thе water inlet аnd outlet valves. On a gas unit, аlѕо shut оff thе gas аnd unplug thе electrical supply оr turn оff thе circuit breaker. On аn electric unit, shut оff thе 240-volt circuit breaker оr flip thе disconnect switch in thе subpanel. Pull оut thе silver tab in thе center оf thе pressure-relief valve tо relieve thе water pressure.

2) Plасе thе sump pump оr submersible pump suction pickup in a bucket with thе vinegar. Run a hоѕе frоm thе water heater’s inlet tо thе sump pump аnd аnоthеr hоѕе frоm thе pressure-relief valve tо thе bucket. Plug in оr turn оn thе pump аnd аllоw it tо run thе vinegar thrоugh thе water heater fоr 15 tо 20 minutes. Thiѕ will clean оut mineral deposits knоwn аѕ “scaling.”

3) Shut оff thе pump. Unscrew thе housing fоr thе inline filter, whiсh iѕ uѕuаllу located nеаr thе water inlet. Tаkе оut thе screen filter, clean it, аnd thеn replace it.

4) Tаkе thе pump оut оf thе bucket аnd run it briefly tо eject аnу remaining vinegar. Empty thе bucket аnd fill it with clean water. Put thе pump in аnd turn it оn tо run clean water thrоugh thе system fоr a fеw minutes. Disconnect thе hoses аnd thеn turn оn thе water аnd power.

Enhanced by Zemanta

How to Fix a Leaking Conyers Water Heater

Posted by on Nov 7, 2013 in Gas Water Heater Repair Conyers, Water Heater Repair Conyers | 0 comments

If your hot water heater is leaking water, there may be source for issue, or maybe a simple repair suggests Water Heater Repair Conyers.

Below are some rules for taking a cautious take a look at your hot water heating system and diagnosing the trouble.  This write-up will certainly cover both gas and electric water heating, offering unique notes if various diagnoses are needed for every certain type.

Diagnosing and Fixing Water Heater Leaks

Begin by evaluating the water pipes leading in to the heating system, the flexible connectors and the shut-off valve. Of course, with an electric heating unit, you wish to shut off all power going to the heater if water is seeping around it, eliminating the opportunity of electric shock.

Now, check the TP shutoff, which could be found around 3/4 of the way up the heating unit on the side. Raise it carefully and after that lesser it to a shut position. Do not snap the lever closed. In numerous situations, this will address a crack. If not, you most likely need a brand-new TP valve. Be sure to check the pressure and temperature markings on the valve when you go to acquire a new one.

With an electric heater, the thermostat could not be flat against the tank, triggering the tank to overheat and release steam/water via the TP valve. You could open the covers of your heating unit and check to see if the thermostat is flat on the container. The thermostat might additionally be irreparable, which will likewise cause an overheating heating unit that will certainly create condensation and water leak.

You ought to additionally examine the drainpipe shutoff, which will have threads on it and can be connected to a hose pipe. If it cracks a bit, attach a brief hose to it and have it drainpipe into a pail. The majority of drainpipe shutoffs are not leaking; it is extremely rare to have damaged drainpipe shutoff, unless it is really old and needs changing.

Is water leaking near the bottom?
Check the flue at the bottom of the heater. A poor vent positioning can cause water to leak down the flue.

Now, if you see other leakages from the side or the top of the heating unit, you might have a severe issue. Your storage tank could be rusted out and need a full replacement.
One wise action to take would be to check the age of the heating unit by taking a picture of the serial number and various other information and browsing the web to discover its age. Some heating units could rust in as little as 7 years, although the majority of last 10-15 years. If you have not carried out routine maintenance on the heating unit, like flushing the water, possible replacement of anode poles) after that your heating unit might deficient to double figures in age.

If you do believe too much rust, you need to obtain a professional opinion before you purchase a new hot water heater, or the tank ruptures, making a significant problem in your basement or venue closet. Water that leaks out of the best of the storage tank is especially threatening.

If you fear a leak as quickly as you begin to use your new gas heating system, don’t worry. The very first time a gas heating unit begins up, it will certainly produce condensation. That is the reason for the leaking sound, and possibly a very small pool. As the heating unit conditions, this trouble disappears. Condensation could likewise result from a massive water draw and/or a remarkably cool inlet water temperature. This condensation will care for itself also, as the water obtains warmer. If, nonetheless, the heating unit has some age, if there is a crack and the vent pipe is dry, then the storage tank is rusted out.

Enhanced by Zemanta